Yamaha YZF 750R 750SP OW01 YZF1000 FZR1000 YEC parts sold

For sale Yamaha YEC temp gauge LCD. 100% working condition, minor scratch on the body, white area to the right of "YEC" logo. Display 100% clear.

For sale Yamaha OW01 modified sprocket cover for cable clutch conversion. Some scratches, 100% working condition. Very rare. Comes with its original, adjustable clutch cable.

For sale Yamaha YZF 750 and FZR 1000 sprocket covers. Minor scratches from normal use, 100% functional. Asking $15 / each. With clutch slave cylinder add $10.

For sale YEC Keihin FCR 39mm Flatslide carburators for Yamaha YZF 750 with YEC airbox. Sold as a kit, carburators, velocity stacks, throttle cable, choke cable and composite airbox. The airbox is smaller volume than the "Mike Walsh" design, it has a bit higher air pressure. The carburators have two accelerator pumps. Needle and jets setup same as per YEC Kit manual. Click to download it.

For sale Yamaha YZF 750 Mikuni BDST 38mm carburators with Dynojet kit installed. Manual with instructions, Dynojet kit jets all included. Carburator ultrasonically cleaned, ready to go.

For sale Yamaha YZF 750 Mikuni BDST 38mm carburators with TPS (throttle position sensor). Quite rare. To take advantage of the TPS sensor and also avoid error codes on the RPM gauge, a correct ignition box (ECU) must be used, as a SET. This ECU (4HD-82305-10) needs a TPS sensor connected, otherwise an error code will be displayed. I firmly believe this set came from the UK for 1995-96 model. I have the lower parts of the carb, as well. It uses SCREW type main jets, NOT push in, as the North American models. Works with North American wire harness.

For sale Yamaha YZF 750 Factory Pro #100120 nickel plated emulsion tubes for Mikuni BDST 38mm carburators.

" Factory Pro manufactures stock replacement needle jets! (called emulsion tubes by some) to original factory specs. The needle jet orifice wears oblong in as little as 10,000 (but commonly 20,000 miles) miles and is particularly aggravated by "in town", low rpm operation. The result is excessive richness at low rpm that can only be partially compensated for by lowering the fuel level. A direct replacement for worn, original items. Accepts standard standard Yamaha jetting and our Factory Pro Carb Recal Kits. Also fits other bikes with 38mm downdraft Mikuni carbs, such as Ducati, TDM 850 / TRX 750 and 800, fzr1000 (89 and up, but not including the Thunder Ace)."

For sale Yamaha YEC run / kill switch. Asking $10

For sale Brembo 320mm Snowflake front brake rotors / disks. 99.99% new. Less than 10km mileage in them. Dark spots on the disks are just fingermarks.

For sale Vance & Hines SS2R Stainless Steel Full Exhaust for Yamaha YZF750. Carbon fiber canister. Oxygen sensor bung. 100% straight, NO dents or anything.

For sale Vance & Hines PowerPak ignition module for YZF750. ALL years! (It can be wired for 93-94 or 95-> models) 100% functional. Comes with a manual.

"A direct descendant of our race team's on-board engine management systems, the PowerPak is designed for the street rider and racer alike, who wants the maximum performance possible for a fraction of the cost. The revolutionary POWERPAK is a device that allows the rider/tuner to select between sixteen different combinations of ignition timing and rev-limit, from stock to as high as 14,000 r.p.m. depending on the specific engine combination or riding application. The rider has the option to use an economical, near-stock setting for everyday use, or with the flick of a switch, select three higher performance ranges. The ignition timing is fully mapped from 2000 r.p.m. to 14800 r.p.m. Included in the circuitry is a fully digital 80c51 microcontroller chip running at 12 megahertz clock speed. This means unmatched accuracy to within 1 r.p.m. All this comes in a machined billet aluminum case that simply replaces the stock ignition black box. Truly the most innovative performance part available at any price, the PowerPak comes with a complete user manual and installs in minutes."

For sale Yamaha YZF 750 ignition coil for cylinders 1 and 4. Fits 1993 and 1994 models.

For sale Yamaha YZF 750 ignition coil for cylinders 2 and 3. Fits 1993 and 1994 models.

For sale Yamaha YZF 750 ignition coil for cylinders 2 and 3. No bracket. Fits 1993 and 1994 models. Asking $15

For sale Yamaha YZF 750 ignition coil set. Fits 1993 and 1994 models. Removed from working bike.

For sale carbon fiber composite YZF 750 gas tank with quick fill cap. 100% functional. Gas tank itself weighs 30oz. or 900gr. You have to feel it to believe it. Ultralight, less than a kilogram. This is the best way to shave off weight from the top of the bike if you need fast corner flipping from one side to the other. Needs little sanding and fresh coat of paint.

For sale Yamaha YZF 750 fuel pump. Fits all models from 1993 to 1998. Ultrasonically cleaned. Tested, works 100%, no leaks or anything. Removed from working bike.

For sale Yamaha YEC alternator cover for YZF 750. Cover had a tiny pinhole from machining, it has been properly repaired from the inside. Absolutely NOT visible from the outside, inside just a small bump (pic no.2). Cover 100% functional.

For sale Yamaha YZF 750 R/SP standard fork axle from '99 Yamaha R1. The axle is a perfect fit, approximately 30gr lighter. 100% straight.

For sale Yamaha YZF 750 pick up coil. Fits 1993-1998 models. 100% working condition.

For sale Yamaha YZF 750 sidestand switch. Fits 93-98 models. 100% functional.

For sale Yamaha YZF 750 alternator, generator, rectifier assembly. 100% working condition for both. Fit 1993 - 1998 models. Picture no.1 is first generation

SOLD

, picture no. 2 is second generaton. Asking $35 / each

AVAILABLE

For sale RADIAL clutch and brake master cylinders with levers and reservoirs. Significantly better modulation than stock, works best with SS braided clutch / brake lines.

For sale R1 front brake caliper and SS braided custom made brake line for YZF750. Russell custom made SS teflon core brake lines, as short as possible. Brand new Ferodo sintered ST pads with less than 10km on them. The caliper pistons are coated with Moly based high temp, low friction coating, and the face with high heat ceramic coating. The body of the caliper is coated with heat dispersant coating. Top notch, racing setup, 10x better than stock! Conversion kit includes the calipers, pads and SS brake lines.

For sale R1 rear brake conversion for Yamaha YZF750. 3mm SS spacer included, custom made SS braided line with Teflon core. Everything ready to go - bolt on solution. Both caliper pistons are coated with high temp Moly based coating on the skirt and ceramic high temp coating on the face. The brake caliper body is treated with a heat dispersant coating on the outside. Conversion kit includes the caliper, brake pads, caliper bracket, 3mm SS spacer and SS braided brake line.

For sale Yamaha YZF 750 cylinder / piston OEM size 72mm set. Looks low mileage. Bolt on solution for worn out engines. I greased the cylinders to prevent oxydation (surface rust). The brownish color inside the cylinder is a mix of the grease and the brown carbon deposit from the top of the cylinder, as I used my fingers to smear the grease around. NO surface rust at all.

For sale Yamaha YZF 750 cylinder / piston oversize set. Pistons are 72.5mm, original Yamaha pistons. Very low mileage. Bolt on solution for worn out engines. Honing and boring is around $200 alone + cylinder + pistons and rings.

For sale Yamaha YZF 750 / FZR 1000 Wiseco 77mm piston and cylinder set. These pistons can make the standard YZF 750cc into a 854cc machine. These pistons have been ultrasonically cleaned. New from Wiseco over $600 USD. The cylinder has a crack on the bottom from poor handling, does NOT effect anything, it should be cut out and ground down.

For sale Yamaha YZF 750 cylinder head assembly. All 12 intake valve guides have been ground down. Other than that nothing else has been done. All valve seats 100% good. Spark plug threads 100% good. All threads, exhaust studs 100% good. The head comes with its 12 intake, 8 exhaust valves, springs and retainers, all 100% good.

For sale Yamaha YZF 750 intake manifold set. The manifolds have been coated with Moly based coatings on the inside, and heat dispersant coating on the outside. Perfect for racers who want to gain every little bit of advantage. Cools the intake manifolds, and on the inside provides very slippery surface for air/fuel mixture.

For sale Yamaha YZF 750 camshaft set. Intake and exhaust. Looking at the bearing surfaces, these camshafts don't have lot of mileage in them. 100% functional, no scratches, no pitting. Nice upgrade for FZR 1000 machines.

For sale Yamaha YZF 750 stock rear wheel. Metalic silver powder coat. 100% straight, good bearings.

For sale Falicon Billet Aluminum clutch basket. Fits YZF750 and FZR1000 models. 100% brand new, never installed. Comes with 3 rivets and 6 springs. I will also include a YZF 750 clutch gear as a bonus. Minor assembly required.

For sale Yamaha YZF 750 standard clutch basket / hub without ring gear. Ultrasonically cleaned, 100% functional. Perfect upgrade for FZR1000 machines.

For sale Yamaha YZF 750 standard clutch basket / hub with ring gear. Ultrasonically cleaned, 100% functional.

For sale EBC SRK9 YZF 750 / OW01 Kevlar clutch rebuild kit. Kevlar fiber lined frictions, new steels, high strength springs. Sets clutch stack to correct OEM height. For use in heavy sport bikes and production-based race bikes. SRK kits have a more aggressive/faster clutch takeup. Full retail $220 + tax.

For sale Yamaha YZF 750 R standard gearbox. Gearbox came from a running / working motor. 100% good.

For sale Yamaha YZF 750 R standard gearbox. Gearbox came from a running / working motor. 100% good.

For sale Yamaha YZF 750 R standard gearbox. Gearbox came from a running / working motor. 100% good.

For sale original Yamaha YZF 750 SP close ratio race gearbox. Very rare part. 100% good.

For sale gorgeous, top of the line Harris rear sets modified for Yamaha YZF 750. Fits all years. These rear sets have a custom made carrier plate (black) to fit the YZF 750 frame mounting holes.

"CNC from solid T-6 6082 billet aluminum. Levers run on self lubricating bearings. Lever position is adjustable on rod end spherical bearings. Footrest position is adjustable (backwards, forwards and up or down). Kit comes with 2 shifting rods. Made in UK."

For sale Yamaha YZF 750 curved radiator. The radiator comes complete with both fans, cap, temperature sensor and fan temperature switch.

"There is an epoxy patch, looks uglier than it really is. I have a feeling someone worked on the exhaust and accidentally ran a tool into the radiator, and then patched it with JB Weld. With a little bit of patience and a small grinder such as a Dremel this patch can be properly "manicured" to make it less visible"

For sale K&N washable air filter for Yamaha YZF 750 standard airbox. Should last a lifetime of the bike. Fits all years. Used, but clean, ready to go.

If you require more information, high res. prictures or anything, please contact me at : mototech@ica.net . I'm a straight forward seller, I try to answer every question that comes my way to my best abilities and knowledge.
I try to provide as many pictures and description as I think is reasonable and feasable due to bandwidth limits, however upon request I can provide even higher resolution pictures for your perusal.
I have tons of parts, this web page will change on a daily basis as I add new items, and/or as they get sold. Check back every couple of days for new listings.

Items still not on the list: Rear sub-frame, OEM full exhaust, carbon fiber passenger seat cover, crankcases, valve covers, and tons of other nuts and bolts... I'll do my best to upload a few items every day. All prices in US Dollars.

Location for shipping/pickup purpose: Mississauga, L4Y 3X7, Ontario, Canada